Problems receiving fax from Rockwell to USR Courier

• Messages sorted by:[ date ][ thread ][ subject ][ author ]

Hi,

I have an embedded modem in some equipment that uses a Rockwell
chipset. When this sends a fax, although it is received fine on a HP
Officejet fax machine, a connection with my USR Courier fails.

I am running mgetty 1.1.20 on Linux. I haven't yet turned up debug
information, but wondered if anyone could help from the following:

This is the notify message from new_fax:
>An incoming fax transmission failed (+FHNG: -6):
>Sender ID:                  732
>Pages received: 0
>
>Modem device: ttyS0
>
>Communication parameters: +FCS:0,2,0,2,0,0,0,0
>    Resolution : normal
>    Bit Rate   : 7200
>    Page Width : 1728 pixels
>    Page Length: unlimited
>    Compression: 0 (1d mod Huffman)
>    Error Corr.: none
>    Scan Time  : 0
>
>Reception Time : 02:10
>
>
>The fax receive was *not* fully successful
>The Modem returned +FHNG: -6
>   (TIMEOUT waiting for modem response (int.))
>
>
>regards, your modem subsystem.

And the mgetty log file:
>--
>05/03 01:38:56 yS0  mgetty: experimental test release 1.1.20-Jan17
>05/03 01:38:56 yS0  check for lockfiles
>05/03 01:38:56 yS0  locking the line
>05/03 01:38:56 yS0  lowering DTR to reset Modem
>05/03 01:38:57 yS0  send: \dATQ0V1H0[0d]
>05/03 01:38:57 yS0  waiting for ``OK'' ** found **
>05/03 01:38:58 yS0  send: ATS0=0Q0&D3&C1[0d]
>05/03 01:38:58 yS0  waiting for ``OK'' ** found **
>05/03 01:38:58 yS0  mdm_send: 'ATI'
>05/03 01:38:58 yS0  non-numeric ID string: '5607B'
>05/03 01:38:58 yS0  USR Courier/Sportster V90 (national variant?) detected
>05/03 01:38:58 yS0  mdm_send: 'ATI3'
>05/03 01:38:58 yS0  additional info: 'USRobotics Courier V.Everything'
>05/03 01:38:59 yS0  mdm_send: 'AT+FCLASS=2.0' -> OK
>05/03 01:38:59 yS0  mdm_send: 'AT+FAA=1;+FCR=1' -> OK
>05/03 01:38:59 yS0  mdm_send: 'AT+FBO=1' -> OK
>05/03 01:38:59 yS0  mdm_send: 'AT+FNR=1,1,1,0' -> OK
>05/03 01:38:59 yS0  mdm_send: 'AT+FLI="+44 (0)1582 479910"' -> OK
>05/03 01:38:59 yS0  mdm_send: 'AT+FCC=1,5,0,2,0,0,0,0' -> OK
>05/03 01:39:00 yS0  waiting...
>05/03 01:46:17 yS0  wfr: waiting for ``RING''
>05/03 01:46:18 yS0  send: ATA[0d]
>05/03 01:46:18 yS0  waiting for ``CONNECT''
>05/03 01:46:25 yS0  found action string: ``+FCO_''
>05/03 01:46:25 yS0  start fax receiver...
>05/03 01:46:25 yS0  fax_wait_for(OK)
>05/03 01:46:26 yS0  fax_id: '+FTI:"                 732"'
>05/03 01:46:27 yS0  transmission par.: '+FCS:0,5,0,2,0,0,0,0'** found **
>05/03 01:46:27 yS0  mdm_send: 'AT+FLO=2' -> OK
>05/03 01:46:27 yS0  fax_send: 'AT+FDR'
>05/03 01:46:27 yS0  fax_wait_for(CONNECT)
>05/03 01:46:35 yS0  fax_id: '+FTI:"                 732"'
>05/03 01:46:36 yS0  transmission par.: '+FCS:0,4,0,2,0,0,0,0'
>05/03 01:46:44 yS0  fax_id: '+FTI:"                 732"'
>05/03 01:46:44 yS0  transmission par.: '+FCS:0,3,0,2,0,0,0,0'
>05/03 01:46:53 yS0  fax_id: '+FTI:"                 732"'
>05/03 01:46:53 yS0  transmission par.: '+FCS:0,2,0,2,0,0,0,0'
>05/03 01:48:27 yS0  Warning: got alarm signal!
>05/03 01:48:27 yS0  mdm_read_byte: read returned -1: Interrupted system call
>05/03 01:48:27 yS0  mdm_get_line: cannot read byte, return: Interrupted system call
>05/03 01:48:27 yS0  fax_get_pages: cannot start page receive
>05/03 01:48:27 ##### fax dev=ttyS0, pid=31148, caller='none', name='', id='                 732', +FHNG=-06, pages=0/0, time=00:02:10
>
>
>05/03 01:48:29 yS0  mdm_send: 'ATH0' -> OK

I would be grateful for any help getting this working.

Regards

Liam
-- 
Liam Whiteside                     |  WhiteSound Audio
Mobile: (0976) 273633              |  Phone: (01582) 479911
Email : liam@whitesnd.demon.co.uk  |  Fax  : (01582) 479910
Email : lwhiteside@iee.org         |  Web  : www.whitesnd.demon.co.uk